Rank: 1

1^# 跳轉到 » 正序看帖

字體大小: tT

發表於 2011-2-23 11:18 | 只看該作者

mobile client

I am seriously looking for a new mobile phone for replacement.

I used to use my WM with Zoiper (beta). However, it cannot work properly now as the IAX connection is broken down.

In the past, YH and Bubblestar 兄 have recommended me on Nokia E63 or E71 for built sip client support.

As my mobile phone is getting worse now, replacement will be shortly.

Therefore, would like seek opinion on next generation phone.

Nokia E series is still on a high side for its cost and giving it intention to migrate to WM7, I am a bit out of interest.
Iphone is also in high price but seems to have a good client SIAX with SIP and IAX2 support. The latter is my favorite

Is there any good android client?

How are their functions compared?

bubblestar

新手上路

Rank: 1

21^#

發表於 2011-2-28 16:37 | 只看該作者

回復 20# ckleea

Yes, you are right.

With the use of Putty, I can get the whole picture of the output message with dmesg.

TOP

ckleea

新手上路

Rank: 1

20^#

發表於 2011-2-28 16:30 | 只看該作者

回復 19# bubblestar

Sorry, I forgot to mention the question is that for CPC and RPT.

dmesg is a standard linux command to look at the output.

However, if you are on a server, the output may be scrolled up much earlier.

TOP

bubblestar

新手上路

Rank: 1

19^#

發表於 2011-2-28 16:05 | 只看該作者

dmesg 應該等於 devices' messages，亦應該就是boot 機時所見的hardware messages。用法比較要插Serial Cable 簡單和方便快捷。

TOP

bubblestar

新手上路

Rank: 1

18^#

發表於 2011-2-28 15:59 | 只看該作者

回復 17# ckleea

Absolutely! This command can detect all hardwares status in our Computer, indeed.

In my case, it shows modules 1 - 4 installed with Auto FXO and FXS respectively.

Also, we can get lots of other information including bluetooth, USB, Dahdi, etc. etc.

Try and you can get more.

TOP

ckleea

新手上路

Rank: 1

17^#

發表於 2011-2-28 15:49 | 只看該作者

回復 14# bubblestar

Thanks. Can these settings be applied to asterisk?

TOP

bubblestar

新手上路

Rank: 1

16^#

發表於 2011-2-28 15:47 | 只看該作者

Rowetel，IP01 的開發者有很好的reference guide，可以看看

Analog Ports

TOP

bubblestar

新手上路

Rank: 1

15^#

發表於 2011-2-28 15:45 | 只看該作者

本帖最後由 bubblestar 於 2011-2-28 16:01 編輯

回復 13# ckleea

可以簡單一些，在PUTTY 入面打

> dmesg

Enter 之後就知道。

正常的話，應該見到

port: 1 port_type: O

****O = FXO port

TOP

bubblestar

新手上路

Rank: 1

14^#

發表於 2011-2-28 15:30 | 只看該作者

回復 10# ckleea

角色兄有時給我用二次撥號打過來也會drop 幾次的。呢個有機會跟CPC (Calling Party Control) 有關，有心機的話可以看這個WEBSITE。

http://michigantelephone.wordpre ... wtork-jitter-level/

http://www.sandman.com/cpcbull.html

我RTP packet size = 0.020。上幾次Drop call 唔關VOIP devices 的事，係NAT Keep Alive 唔記得Enable。
現在一有時間，我反而開始集中注意力在VoIP 通話的優化及提升質素方面，嘗試找出原因改善，否則有靚靚的ATA 或 Asterisk 都係浪費。

TOP

ckleea