ckleea

回復 90# bubblestar


    Thanks. You are really hardworking in looking at the manual.

bubblestar

回復 91# ckleea




Oh! not really.  The content that I found was just an unexpected disovery.  I skimmed the manual instead read.  It will kill me if I read such a thick manual of over 270 pages as a mini Yellow Page Telephone Directory.

ckleea

剛剛發覺，如果將router port forwarding to  IP01, 最好都是用 port 80。試過唔同 ports, timeout 機會大好多。

註: IP01 放在外國

bubblestar

你說的是Remote Management 去 access IP01 嗎? 外國並沒有Block port 80 ?? 沒有的話，當然是最理想的了。

ckleea

回復 94# bubblestar


外國連線速度慢，所以出現 timeout。

如果用商業boardband 就不是問題，家用的bandwifth就不保證

ckleea

回復 94# bubblestar


外國連線速度慢，所以出現 timeout。

如果用商業boardband 就不是問題，家用的bandwifth就不保證

角色

有多慢呢？上载是多少，下载又是多少呢？

角色

bubblestar

想請教一下有沒有人知道如何在ATCOM IP01 建立及使用 SipToSis

ckleea

You need to have a version of skype running. i.e. you need another PC computer in the same LAN to run skype.

角色

In fact, in the past I ran SipToSis on a notebook platform. But in the fast, I shall consider to buy an ATOM-based PC such that we may install whatever software that we want including SipToSis and CentOS.

YH

yiucsw

求救！
原本是通过et263将北京的SPA3102 连到 香港的draytek声音一直很好。因要从北京搬到Macau，所以要, 中国的北京手机呼转到IP01,然后将转到我香港和Macau的手机。为了这次搬迁买了“GSM的无线接入台”和“IP01”。连到我的北京的SPA3102，尝试了几天还不能调好，后天要搬家，所以要求教。
有没有现有的Config可以拷贝？
1）我的香港vigor 2910Vn 一直连不到IP01, 不知道原因。 Symmetric RTP 也不成。
2） GSM接入平台连北京SPA3102，用ET263长途声音可以。但连到vigor2910v 回音很重。
3）router reboot 后，IP01 要Reboot 才拿到IP。

yiucsw

求救！
原本是通过et263将北京的SPA3102 连到 香港的draytek声音一直很好。因要从北京搬到Macau，所以要, 中国的北京手机呼转到IP01,然后将转到我香港和Macau的手机。为了这次搬迁买了“GSM的无线接入台”和“IP01”。连到我的北京的SPA3102，尝试了几天还不能调好，后天要搬家，所以要求教。
有没有现有的Config可以拷贝？
1）我的香港vigor 2910Vn 一直连不到IP01, 不知道原因。 Symmetric RTP 也不成。
2） GSM接入平台连北京SPA3102，用ET263长途声音可以。但连到vigor2910v 回音很重。
3）router reboot 后，IP01 要Reboot 才拿到IP。

yiucsw

求救！
原本是通过et263将北京的SPA3102 连到 香港的draytek声音一直很好。因要从北京搬到Macau，所以要, 中国的北京手机呼转到IP01,然后将转到我香港和Macau的手机。为了这次搬迁买了“GSM的无线接入台”和“IP01”。连到我的北京的SPA3102，尝试了几天还不能调好，后天要搬家，所以要求教。
有没有现有的Config可以拷贝？
1）我的香港vigor 2910Vn 一直连不到IP01, 不知道原因。 Symmetric RTP 也不成。
2） GSM接入平台连北京SPA3102，用ET263长途声音可以。但连到vigor2910v 回音很重。
3）router reboot 后，IP01 要Reboot 才拿到IP。

Qnewbie

If you mention the backup of SPA3102 setting, please read the HK voip manual, edited by Yhfung C-hing.

I don't have GSM AP and IP01. So I cannot answer the other question exactly.
1) What is your IP type in HK, is it static or dynamic?
2) What is the latency between vigor & SPA3102? If the latency is large, the echo-cancelling might not work.
3) Router reboot, it might took a while as IP01 knows the NEW ip address. Try to reduce the ip lookup time or similar  (something like the SPA's Register Expires time) to let IP01 updates the vigor's IP.

I am interested in the “GSM的无线接入台”+SPA3000 as GSM gateway. Hopeful you can provide more valuable detail in the future.

yiucsw

I want to have an complete IP01 setting instead of SPA3102.
Both HK, China, and future macau is dynamic IP.
The latency is acceptable with vigor & SPA3102 thru ET263 directly, but cannot register vigor with IP01. As I need to add GSM 无线接入台 which will add another latency, so i need to bypass ET263 and register to IP01.
3) Router reboot, IP01 do not have a keep alive signal which check if an new NEW ip address was assigned.

For “GSM的无线接入台”+SPA3000 as GSM gateway. There are two kind of GSM, either provide FXO or FXS. except for the off hook voltage issue, seems the machine work fine for more than 5 days. (except the SMS/MMS seems to be disappeared.)