Elastix + OpenVox D430E問題

saidee

各位,

小弟最近裝了OpenVox D430E上Elastix server，之後發現不能打出打入，但T1 signalling正常，試過Debug，搵到下面Warning, 因為我係Elastix新手，上網搵過都唔係好知點fix，有無師兄可指教？

(Snip from Full.log)
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Executing [25123123@from-internal:1] Dial("SIP/1002-0000000e", "dahdi/g0/25123123") in new stack
[May 28 10:16:40] WARNING[9278] channel.c: No channel type registered for 'dahdi'
[May 28 10:16:40] WARNING[9278] app_dial.c: Unable to create channel of type 'dahdi' (cause 66 - Channel not implemented)
[May 28 10:16:40] VERBOSE[9278] app_dial.c:   == Everyone is busy/congested at this time (1:0/0/1)
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Executing [25123123@from-internal:2] Hangup("SIP/1002-0000000e", "") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:   == Spawn extension (from-internal, 25123123, 2) exited non-zero on 'SIP/1002-0000000e'
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Executing [h@from-internal:1] Macro("SIP/1002-0000000e", "hangupcall") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Executing [s@macro-hangupcall:1] GotoIf("SIP/1002-0000000e", "1?endmixmoncheck") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Goto (macro-hangupcall,s,9)
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Executing [s@macro-hangupcall:9] NoOp("SIP/1002-0000000e", "End of MIXMON check") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Executing [s@macro-hangupcall:10] GotoIf("SIP/1002-0000000e", "1?nomeetmemon") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Goto (macro-hangupcall,s,28)
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Executing [s@macro-hangupcall:28] NoOp("SIP/1002-0000000e", "End of MEETME check") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Executing [s@macro-hangupcall:29] GotoIf("SIP/1002-0000000e", "1?noautomon") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Goto (macro-hangupcall,s,34)
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Executing [s@macro-hangupcall:34] NoOp("SIP/1002-0000000e", "TOUCH_MONITOR_OUTPUT=") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Executing [s@macro-hangupcall:35] GotoIf("SIP/1002-0000000e", "1?noautomon2") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Goto (macro-hangupcall,s,41)
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Executing [s@macro-hangupcall:41] NoOp("SIP/1002-0000000e", "MONITOR_FILENAME=") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Executing [s@macro-hangupcall:42] GotoIf("SIP/1002-0000000e", "1?skiprg") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Goto (macro-hangupcall,s,45)
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Executing [s@macro-hangupcall:45] GotoIf("SIP/1002-0000000e", "1?skipblkvm") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Goto (macro-hangupcall,s,48)
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Executing [s@macro-hangupcall:48] GotoIf("SIP/1002-0000000e", "1?theend") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Goto (macro-hangupcall,s,50)
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Executing [s@macro-hangupcall:50] AGI("SIP/1002-0000000e", "hangup.agi") in new stack
[May 28 10:16:40] VERBOSE[9278] res_agi.c:     -- Launched AGI Script /var/lib/asterisk/agi-bin/hangup.agi
[May 28 10:16:40] VERBOSE[9278] res_agi.c:     -- <SIP/1002-0000000e>AGI Script hangup.agi completed, returning 0
[May 28 10:16:40] VERBOSE[9278] pbx.c:     -- Executing [s@macro-hangupcall:51] Hangup("SIP/1002-0000000e", "") in new stack
[May 28 10:16:40] VERBOSE[9278] app_macro.c:   == Spawn extension (macro-hangupcall, s, 51) exited non-zero on 'SIP/1002-0000000e' in macro 'hangupcall'
[May 28 10:16:40] VERBOSE[9278] pbx.c:   == Spawn extension (from-internal, h, 1) exited non-zero on 'SIP/1002-0000000e'


(From dahdi-channels)
; Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER)
group=0,11
context=from-pstn
switchtype = 4ess
allow=ulaw
signalling = pri_cpe
channel => 1-23
context = default
group = 63

(From system.conf)
# Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER)
span=1,1,0,esf,b8zs
echocanceller=mg2,1-23
# termtype: te
bchan=1-23
dchan=24

alexccy

What Carrier you are using? in debug mode > Call your T1 Phone no. > check what is output?

saidee

We are using PxxW, and I can see the channels are in service from hardware detector page, but I cannot make any call or receive call. From the debug mode, when I call the T1 number, there is nothing happen, and when I make outbound call, have below error,

"TRUNK Dial failed due to CHANUNAVAIL (hangupcause: 66)".

What would be the possible cause for this?
Million thanks.

角色

Have you checked with the supplier of your T1 card about the correct Asterisk driver to be used?

alexccy

Make sure the pin assignment is right? and  "PRI Switch Type" is right , you can try 4ESS or NI2