OBiApps to use OBi110 as voice gateway

ckleea

In ObiApps, I can add an OBi110 as voice gateway. In the manual, it says, speed dial + * + tel  number will use the OBi110 to dial out.

I can do this but always via SP1 i.e. google voice line.

Is there any way to dial out via SP2 or PSTN?

角色

Yes, you are able to do it. The dialling method is show below:

<speed dial> + <*> + <tel number> (This goes to the primary trunk (line) of the callee for one-stage dialling using the speed dial method).

<speed dial> + <**1> + <tel number to SP1>
<speed dial> + <**2> + <tel number to SP2>
<speed dial> + <**8> + <tel number to PSTN>
<speed dial> + <**9> + <tel number to OBiTalk>

The caller with the firmware 1.2 or above will strip off the first "*" and send it to callee's primary trunk. If the default primary trunk of the callee is SP1, the caller's outgoing information will send to the SP1 via the SP1's inboundcallroute. As a result, the callee SP1 inboundcallroute should direct the caller's information to the corresponding trunk as follows:

{<*1> + <tel number to SP1>:sp1}
{<*2> + <tel number to SP2>:sp2}
{<*8> + <tel number to PSTN>:li}
{<*9> + <tel number to OBiTalk>:pp}

If your default for <speed dial> + <*> is PSTN trunk, you have to modify the inboundcallroute for the callee's PSTN trunk.


YH

ckleea

It does not work in my case.

角色

You have to rewrite the inboundcallroute of the primary trunk of your OBi110 device. In your case, the default primary trunk is SP1.

YH

bubblestar

回復 3# ckleea


YH's explanation is correct.  I have been using this for voice gateway for almost 2 weeks without problem. The OBiAPP number has to be included in your Speed Dial list to make it work.

In your case, the OBiAPP is integrated into Asterisk now (using VNC and WINE way), the voice gateway dialing might not be the same as normal practice.  I think we have to figure out another way to fine tune the dial plan in Asterisk to accommodate OBiApps in this regard.

ckleea

回復 5# bubblestar


I still can't make it work. Will try later.

However, when I look at the call status screen when dialing, it shows up correctly as using SP1 or phone

There is an interesting follow up here at Obi forum

http://www.obitalk.com/forum/index.php?topic=604.0

I have removed the need of VNC and Gnome now.

VNC is just for checking the status.

ckleea

I got success now.

I modify the inbound callroute at Obitalk service as {>(xx.):li},{aa}

However, I would like to have a plan like this

2 - 9 xxxxxxx > line
1 xxx xxx xxx > SP1 (Google voice)

Please advise.

ckleea

I am using this but not working for SP1

{>(1xxxxxxxxx):sp1},{>([2-9]xxxxxxx):li},{aa}

ckleea

Updated

Obitalk Service > InboundCallRoute
{(290xxxxxx)>(xx.):SP1},{(290xxxxxx)>(<**2:>xx.):sp2},{(290xxxxxx)>(<**8:>xx.):li},{(290xxxxxx):aa},{ph}

dialing 10 digits uses the default - sp1

dialing **2 + 10 digits uses sp2

dialing **8 + 10 digits uses the line

角色

What is the result with the setting in 9#? Are you able to make it?

YH

ckleea

回復 10# 角色


    Only this {>([2-9]xxxxxxx):li},{aa} work for me.

ckleea

I got the right syntax now. It works for me as {>(<*1:>xx.):sp1},{>(<*2:>xx.):sp2},{>(<*8:>xx.):li},{>(<*9:>xx.):pp},{aa}

But since I use softclient via asterisk, it passes me different callerid. I have to figure a way to restrict the usage.

Thanks

bubblestar

回復 12# ckleea


   
For security sake, it is advised to let the authorized number to dial thru the gateway.  Your syntax seems to allow everyone to use the voice gateway now.

角色

回復 12# ckleea
ck,

What is the function of the first right angle bracket (">") in your inboundcallroute {>(<*1:>xx.):sp1}, what happens if we change it to {(<*1:>xx.):sp1}?

YH

ckleea

I don't know. Initially it is bound by specific caller ID. But I am in a trust user environment and so I delete the 290xxxxxxx. It works.