電訊茶室 - Powered by Discuz! Board

標題: Elastix + OpenVox D430E問題 [打印本頁]

作者: saidee 時間: 2013-5-28 10:38 標題: Elastix + OpenVox D430E問題

本帖最後由 saidee 於 2013-5-28 10:40 編輯

各位,

小弟最近裝了OpenVox D430E上Elastix server，之後發現不能打出打入，但T1 signalling正常，試過Debug，搵到下面Warning, 因為我係Elastix新手，上網搵過都唔係好知點fix，有無師兄可指教？

(Snip from Full.log)
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Executing [25123123@from-internal:1] Dial("SIP/1002-0000000e", "dahdi/g0/25123123") in new stack
[May 28 10:16:40] WARNING[9278] channel.c: No channel type registered for 'dahdi'
[May 28 10:16:40] WARNING[9278] app_dial.c: Unable to create channel of type 'dahdi' (cause 66 - Channel not implemented)
[May 28 10:16:40] VERBOSE[9278] app_dial.c: == Everyone is busy/congested at this time (1:0/0/1)
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Executing [25123123@from-internal:2] Hangup("SIP/1002-0000000e", "") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c: == Spawn extension (from-internal, 25123123, 2) exited non-zero on 'SIP/1002-0000000e'
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Executing [h@from-internal:1] Macro("SIP/1002-0000000e", "hangupcall") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Executing [s@macro-hangupcall:1] GotoIf("SIP/1002-0000000e", "1?endmixmoncheck") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Goto (macro-hangupcall,s,9)
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Executing [s@macro-hangupcall:9] NoOp("SIP/1002-0000000e", "End of MIXMON check") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Executing [s@macro-hangupcall:10] GotoIf("SIP/1002-0000000e", "1?nomeetmemon") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Goto (macro-hangupcall,s,28)
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Executing [s@macro-hangupcall:28] NoOp("SIP/1002-0000000e", "End of MEETME check") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Executing [s@macro-hangupcall:29] GotoIf("SIP/1002-0000000e", "1?noautomon") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Goto (macro-hangupcall,s,34)
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Executing [s@macro-hangupcall:34] NoOp("SIP/1002-0000000e", "TOUCH_MONITOR_OUTPUT=") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Executing [s@macro-hangupcall:35] GotoIf("SIP/1002-0000000e", "1?noautomon2") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Goto (macro-hangupcall,s,41)
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Executing [s@macro-hangupcall:41] NoOp("SIP/1002-0000000e", "MONITOR_FILENAME=") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Executing [s@macro-hangupcall:42] GotoIf("SIP/1002-0000000e", "1?skiprg") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Goto (macro-hangupcall,s,45)
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Executing [s@macro-hangupcall:45] GotoIf("SIP/1002-0000000e", "1?skipblkvm") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Goto (macro-hangupcall,s,48)
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Executing [s@macro-hangupcall:48] GotoIf("SIP/1002-0000000e", "1?theend") in new stack
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Goto (macro-hangupcall,s,50)
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Executing [s@macro-hangupcall:50] AGI("SIP/1002-0000000e", "hangup.agi") in new stack
[May 28 10:16:40] VERBOSE[9278] res_agi.c:    -- Launched AGI Script /var/lib/asterisk/agi-bin/hangup.agi
[May 28 10:16:40] VERBOSE[9278] res_agi.c:    -- <SIP/1002-0000000e>AGI Script hangup.agi completed, returning 0
[May 28 10:16:40] VERBOSE[9278] pbx.c:    -- Executing [s@macro-hangupcall:51] Hangup("SIP/1002-0000000e", "") in new stack
[May 28 10:16:40] VERBOSE[9278] app_macro.c: == Spawn extension (macro-hangupcall, s, 51) exited non-zero on 'SIP/1002-0000000e' in macro 'hangupcall'
[May 28 10:16:40] VERBOSE[9278] pbx.c: == Spawn extension (from-internal, h, 1) exited non-zero on 'SIP/1002-0000000e'

(From dahdi-channels)
; Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER)
group=0,11
context=from-pstn
switchtype = 4ess
allow=ulaw
signalling = pri_cpe
channel => 1-23
context = default
group = 63

(From system.conf)
# Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" (MASTER)
span=1,1,0,esf,b8zs
echocanceller=mg2,1-23
# termtype: te
bchan=1-23
dchan=24

作者: alexccy 時間: 2013-5-28 12:30

What Carrier you are using? in debug mode > Call your T1 Phone no. > check what is output?

作者: saidee 時間: 2013-5-28 13:11

We are using PxxW, and I can see the channels are in service from hardware detector page, but I cannot make any call or receive call. From the debug mode, when I call the T1 number, there is nothing happen, and when I make outbound call, have below error,

"TRUNK Dial failed due to CHANUNAVAIL (hangupcause: 66)".

What would be the possible cause for this?
Million thanks.

作者: 角色 時間: 2013-5-28 21:04

Have you checked with the supplier of your T1 card about the correct Asterisk driver to be used?

作者: alexccy 時間: 2013-5-29 12:11

本帖最後由 alexccy 於 2013-5-29 12:17 編輯

Make sure the pin assignment is right? and "PRI Switch Type" is right , you can try 4ESS or NI2

歡迎光臨電訊茶室 (http://telecom-cafe.com/forum/)