標題: How to forward my OBiTalk call to the HK number I entered through PSTN line? [打印本頁] 作者: mwpmo 時間: 2011-3-25 16:27 標題: How to forward my OBiTalk call to the HK number I entered through PSTN line?
本帖最後由 mwpmo 於 2011-3-25 16:28 編輯
When I am not in Hong Kong, I wish to use the OBiON in my iPhone to call my OBi110 in Hong Kong and then need my OBi110 to answer my call, ask me the HK number I wish to dial and then forward my call to that Hong Kong number using PSTN.
How can I set the Auto Attendant Setting so that it only auto answer from my OBi number assigned to my iPhone only but not other OBi number or call from PSTN?
Any other setting I need to set?作者: 角色 時間: 2011-3-25 16:37
1) Use the OBiTalk portal to include all your OBi endpoints including your PC OBiAPP, OBiON app for iPhone, HK OBi110 to '"My OBi Endpoints"
2) Set your HK OBi110's primary line (trunk) to be the LINE port
3) Using your OBiON app for iPhone, use the one-stage dialling method to make HK PSTN calls directly without entering the Auto Attendant (AA) mode
<speed dial> * <HK PSTN number>
where <speed dial> is a number of [1-99] containing the OBi Number of HK OBi110 PSTN Gateway.
For example, if the speed dial for the HK OBi110 is 3 and HK PSTN number to be called is 22334455, the key sequence on your OBiON in iPhone is
3*22334455
YH作者: mwpmo 時間: 2011-3-25 17:23
本帖最後由 mwpmo 於 2011-3-25 17:30 編輯
Thanks a lot for your assistance.
But my Obi110 fail to forward my call, it just keep ringing.
Since I use WebUI, I disabled the "Auto Provisioning" function in my OBi110 (as suggested by OBIHAI). So OBiTalk Portal cannot setup my OBi110 and hence don't have the information of my OBi number of my iPhone. Is it the reason why OBi110 don't forward my call?
In OBiTalk web portal, I tried to add my OBi110 as the voice gateway of my iPhone's OBi number, but the case is just the same.作者: 角色 時間: 2011-3-25 17:26
Have you updated the firmware version 1.2?
This is a new feature in the firmware version 1.2.
YH作者: mwpmo 時間: 2011-3-25 17:31
I am using 1.2, what is the new feature?作者: ckleea 時間: 2011-3-25 17:37
speeddial + * + HK Number
or
speeddial + **8 + HK Number
I already check the default port for both "Phone Port" & "Line Port" are PSTN (Default)
Is it the location of the "Primary Trunk" setting?
Cause I cannot find a setting "Primary Trunk".作者: 角色 時間: 2011-3-26 16:46
Primary Trunk is my word. OBi uses Primary Line.
YH作者: mwpmo 時間: 2011-3-26 23:08
本帖最後由 mwpmo 於 2011-3-26 23:27 編輯
So the Primary Line setting was already set to "PSTN".
I still don't know why I use <speed dial> * <HK Phone number> or just the <HK Phone number> (I already added my OBi110 as the gateway for my OBi no for my iPhone), my OBi110 just ring without forwarding my call to that HK number?
Any idea?
Is it because I disable "Auto Provisioning" in my OBi110?作者: 角色 時間: 2011-3-26 23:13